Chips serial sequence number

When looking at a chip number we recommend that you: Read the first three digits. If the number made by the first three digits is between and , this is not the country code but the manufacturer code issued by ICAR. If the number is below , it is probably the country code. There are some concerns about the However, you will have either direct information on the animal's country of origin if the chip includes the country code or indirect information through "europetnet" if the first three digits indicate the manufacturer and they have transmitted the information to Europetnet.

The identification of domestic animals is a regulatory obligation. This rule has gradually been extended to all domestic carnivores dog, cat, ferret. In the following sample, 4-byte serial numbers starting at 0x12D68 shall be programmed at address 0x Now J-Flash is prepared to program the 8-byte serial number. The following chapter provides an overview of the program settings. Both general and per project settings are considered.

The default device number is 0. For connections via the J-Link Remote Server the according connection string may be entered. Select the Engineering radio button when setting up a project or select the Simplified radio button when using J-Flash in production environments. In the simplified user interface some options are disabled to reduce possible error sources in the production phase.

The interface speed used before and after initialization can be configured. The interface speed before init is used to communicate with the target before and during execution of the custom initialization sequence described in the section Init steps. The interface speed after init is used to communicate after executing the custom initialization sequence.

This is useful if a target running at slow speed and the users wants to set up a PLL in the initialization sequence. The position of the device to connect with J-Flash is selected from the Position dropdown menu. This works fine for ARM only scan chains. J-Flash can be used to program both external or internal flash memory. In order to use J-Flash with an external flash device, the proper Core must be selected.

To program internal flash devices, the respective microcontroller must be selected in the Device list by clicking the Select the respective microcontroller from the list to program internal flash devices.

In order to program external flash, select the device or core from the list. The compatible endianness of the selected device is set automatically if possible.

Otherwise, select little endian or big endian from the dropdown menu accordant to the device. The core ID for all listed devices is known, therefore this value is filled in automatically if a device is selected and can not be modified. If only a core family is selected, the core ID field can be modified. This option allows the user to mask out specified bits of the core ID. Many microcontrollers require an initialization sequence for different reasons: When powered on, the PLL may not be initialized, which means the chip is very slow, or a watchdog must be disabled manually.

To use these chips the user must first perform the required initialization. This dialog allows the user to enter a custom initialization sequence using a predefined list of operations. After choosing an operation and corresponding values to be associated with the operation, a comment may be added to make it easier for others to determine its effect.

The following list shows all valid commands which can be used in an init sequence:. Flash memory can only be influenced by altering the data file. Those steps will be performed immediately after the target has been successfully programmed. The Exit steps can be used to do some special handling after programming, for example to set some security bits in order to secure the chip. This dialog is used to select and configure the flash device to operate with.

If a core family has been selected in order to program external flash memory or a custom Flash Bank has been added and is selected, the menu should look similar to the screenshot below. If a specific device has been selected to program the flash of these device, the menu should look similar to the screenshot below. The Disable flash bank checkbox disables the flash bank currently selected in the dropdown menu, which can be used to change which flash banks are processed by J-Flash with only one click per flash bank.

This is especially useful when testing different configurations. The final section of this dialog indicates the sectors to be affected by erase, read and write operations done by J-Flash. An individual or series of sectors may be selected from the predetermined valid range.

For some flashes e. The organization settings make it possible to configure the bus width and the number of flash chips connected to the address and data bus of the MCU. There are two other checkboxes that are of interest in this subsection which are Check manufacturer flash Id and Check product flash Id. These checkboxes should be selected to confirm the type of device that is in communication with J-Flash.

Delay before start defines the delay in ms after enabling the target power supply and before starting to communicate with the target. Discharge target on disconnect causes a discharge of any capacities left on the target on disconnect. Enabling VTref monitor causes the Flasher to monitor the target voltage VTref in stand- alone mode and makes the Flasher throw an error when the voltage drops below the min- imum or rises above the maximum during programming.

J-Flash supports programming of serial numbers into the target in two ways. For a detailed description on how to use the serial number programming feature please refer to Serial number programming. The settings in this section are taken account for stand-alone configurations, only. For more information on how to use J-Flash for Flashers in stand-alone mode, please refer to the Flasher User Guide chapter " Setting up Flasher for stand-alone mode ". If Perform blank check is checked, a blank check will be performed before an erase.

If the area to erase is already blank, no erase happens. This specifies the log level of J-Flash. Increasing log levels result in more information logged in the log window. If this option is checked, a file name of the J-Link logfile can be specified. The J-Link logfile differs from the log window output of J-Flash.

However, all of this information is kept confidential within the system, and each participant's information is linked to a six-digit code, which is referred to as the CHIPS UID. This simplicity reduces the occurrence of errors in transaction entry and speeds up the process for all parties.

Also, because the CHIPS UID number is linked to but does not reveal banking information such as an account number, the structure of this clearing system prevents a biller from knowing a payer's banking information. This increases the security and confidentiality of the system. Actively scan device characteristics for identification.

Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile.

Or the second option is with the Dallas DS, separates a unique pin Wire one , this number is unique. How to read the ID serial number of an Arduino? Hi all, Is there a way to retrieve the ID serial number on the sticker on the back of the Arduino, e. Thanks a lot, but i wonder, can the Arduino send this ID via serial? I am making a flexible network of arduino-embedded interactive components.

Thanks HCF, that was the exact code I was looking for.