Cap hpr-1 manual

Core Drill - CD10 2 Pages. Power Units - GT18 2 Pages. Sinker Drill - SK47 2 Pages. IW12 3 Pages. IW16 2 Pages. Hammer Drill - HD08 2 Pages. Core Drill - CD12 2 Pages.

Rail Drill - RD12 2 Pages. Rail Drill - RD11 2 Pages. Safe Bond 2 Pages. Cup Stone Grinder 2 Pages. Drill 2 Pages. Profile Grinder 2 Pages. Underwater Grinder 2 Pages. Vertical Grinder 2 Pages. Tie Tampers 2 Pages. Tamper 2 Pages. Dewatering Pump 2 Pages. Trash Pump 2 Pages. Diaphragm Water Pump 2 Pages. Hydraulic Post Puller 2 Pages. Earth Auger 2 Pages.

Gas Rail Saw 2 Pages. Small Hydraulic Power Unit 2 Pages. Diamond Chain Saw 4 Pages. Hydraulic Breaker 2 Pages. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Remove all. The factory recommended settings for your G6R are:. Once these baseline pressures are set, you can fine-tune your pressure settings over a chronograph. O-ring replacement kits and maintenance kits, as well as F1 approved marker lube is available here: Parts Kits and Marker Lube. Although this usually takes a lot of time and use, it is something that happens gradually over time and has a big effect on velocity. As your poppet seal wears, you will need to increase your pressures to maintain the velocity you want to play with.

If you decide to replace your poppet seal, be very careful to not foul the sealing edge of the body, as this cannot be repaired and is costly to replace. This brass part is the back of your hose barb. It should be fully seated and not protruding from it's recessed hole. This problem does not arise often but is easy to check. This is one of the more difficult issues to diagnose as there is not really a good test other than replacing with a new solenoid and seeing if the issue is resolved.

Most people will send their marker to the service center if they have checked all of the other listed issues and they suspect that they may be having an issue with their solenoid.

The solenoid is one of the more costly and labor-intensive parts to replace, so all of the other areas of the marker should be inspected and maintenance performed before it is replaced. Your paintball marker can leak from different areas for a variety of reasons. The best way to detect where the leak is coming from is to air up the marker and listen or use a diluted mild soap and water mixture on the outside of the gun to check for bubbles.

DO NOT submerge your marker in water and do not over-apply the soapy water mixture. Work in small areas of the marker and dry off the marker when you are done looking for the leak. Do not fire the marker while it is close to your ear Turn the marker off before checking for leaks.

If you can identify where the leak is coming from, you can most likely fix the leak by replacing a seal or o-ring. Here is a list of common areas where leaks can occur in the G6R and the basic method to fix it:.

You can replace the poppet seal by separating the 2 body halves and replacing the white seal on the poppet shaft. Be sure to not foul or damage the sealing edge of the new poppet seal or body. This repair should be done in a clean environment.

Do not stick a tool inside the body where the poppet seals against the body. If the body is damaged in this area, it cannot be repaired and is costly to replace.

There are a number of stationary o-rings inside the marker that allow air to travel to different areas of the marker without the use of external hoses. We care about data privacy, which we consider to be a fundamental human right. To that end, we adopted a series of administrative and technical procedures in order to strengthen the protection of your right to personal data protection.

Required cookies are those that are used solely for the purpose of transmitting a communication and those that are absolutely necessary for a website to provide the service that a user is requesting.

Examples include an authentication cookie that identifies a user for the duration of the session once that user logs in to a website or a cookie that keeps track of items placed in an e-commerce shopping cart. Personalization cookies are those that enable a user to access a website and receive services that are catered to that user's pre-defined characteristics, such as language, browser type used to access the service, regional configuration from where the service is accessed, etc.

Allow Personalization Cookies. Analytics cookies are those that enable the monitoring and analyzing of the behavior of users of a website.

The information gathered through such cookies is used for measuring the activity of the website, platform or application and for profiling the navigation of users of the website, platform or application, in order to improve the website based on that analysis.

Allow Analytics Cookies. The third-party cookies procedures are managed and controlled exclusively by each provider in accordance to their own privacy policies.